- Home
- Batteries add remove
-
Solar Prod
add remove
-
Electricals
add remove
-
Electronics
add remove
Crocodile Clip
add remove- Coils add remove
- Transistors and IC'S
- Speakers add remove
- Converters
- Glue
- Capacitors
- Diodes
- Computer Acc add remove
- CCTV Cam add remove
- Contact
Hand Blower Wire with 3 wires
Reference:
This is a Wire which is connected to a Hand Blower.
Used as Power supply for Hand Blowers.
This is a Wire which is connected to a Hand Blower.
in the same category
Coupler
2 RCA Female input 1 RCA Male Output
RCA means (Radio Corporation of America).
An electrical connector used to carry audio or video signals.
Tweeter Voice Coil 75.5mm
- These are used to create Sound Waves when used in a tweeter.
- 75.5 mm
Amplifier Circuit
The purpose of the circuit is to increase (amplify) the input signal to produce output signal at a higher length than that of the input signal.
Complete Drum Set
A set of drums which has drum sticks, bass drum,floor tom,tom rack and a snare drum, crash cymbal and a Hi-Hat.
Circuit for Chogo TV 14 inches to 21 inches
- TV circuit for Chogo TV ( Box TV)
- Ranges from 14 inches to 21 inches
High Quality Speakers 15 inches 600 Watts
Uses 75.5 MM coil (Available on site search >electronics>coils )
15 inches 600 Watts 8 OHMS speaker.
A speaker is used to generate sound and radiate it into a room or open air.
Are connected to electrical sound devices to amplify the frequency of the sound depending on the watts of the speaker.
A speaker is used to generate sound and radiate it into a room or open air.
Are connected to electrical sound devices to amplify the frequency of the sound depending on the watts of the speaker.
Amplifier with IC TDA 7297
This device is used to increase the power of a signal.
Amplifier with IC TDA 7377
This device is used to increase the power of a signal.
TEA 2025
- Monolithic Integrated Audio amplifier IC in a 16-Pin Plastic dual in Line Package.
- Semi-conductor device
- Amplifies or switches electronic signals and electrical power.
- Regulates Current
TPA 3116
- Good Quality Sound and Power to go with the Speaker
- Voltage Supply is 10V to 25V DC
- Semi-conductor device
- Amplifies or switches electronic signals and electrical power.
- Regulates Current
Car Amplifier
- Boosts Small Electrical audio signal from the Head Unit to produce a higher voltage.
- Clarifies Sound and Volume by Enhancing the Power when connected to Car Speakers
- Strengthens a Weak Audio System.
Multimeter UT33B+
Modern Digital Multimeter UNI-T brand.
A multimeter is an electronic device which is commonly used to measure the voltage , current and resistance.
Can be termed as Multi-tester or a Volt/Ohm Meter.
Tests continuity of two points in an Electric circuit.
Coupler Mono Output 6.3 MM.
2 RCA Female input Mono Output 6.3 MM.
RCA means (Radio Corporation of America).
An electrical connector used to carry audio or video signals.
Ceiling Speakers 60w
This is a rectangular shaped ceiling speaker
- Receive power by speaker cables and external amplifiers.
- Each speaker is wired to the binding posts of the AMP
- 60 w speaker
- Very flexible for one spot daily usage for long period of time i.e years and more.
- Saves floor space and looks organized .
Speaker Subwoofer 15 W 8 ohms
- Produces Low pitched audio frequencies
- Enables Bass sounds
Amplifiers *14 2SC 5200 and 14 2SA 1943
This is the main or port of an amplifier which controls and performs the function of Amplifiers.
Canon Pin Male and Female
Electrical connector used for audio signals in microphones.
Brown PCB Board *9 cm by 7 cm*
PCB - Printed Circuit Board
- Used to connect electronic components together by soldering
Amplifiers *8 2SA 5200 8 2SC 1943
This is the main or port of an amplifier which controls and performs the function of Amplifiers.
Super LED light tester
- Measures voltage of LED Bulbs.
- Can tell us the voltage of an LED bulb individually or many bulbs connected together and also light beads in the same manner.
- AC input 85V-265V AC.DC Output; 0v to 300v DC.
- Model;CA-300V.
- Automatically identify Lamp Beads and Light Bay.
- DO NOT TOUCH BOTH ENDS OF THE PROBES AT THE SAME TIME.
- DISCONNECT POWER WHEN NOT IN USE.